|
|
 |
|
|
 |
 |
 |
 |
 |
 Side by Side |
|
| Where to lnstall
| Door Removal
| Mount the freezer and doors | Feed water pipe Installation |
|
 |
|
 Where to lnstall
 |
|
Strong and even
floor
Unstable installation may cause vibration and noise.
If the floor to install the refrigerator on is not
even, make the refrigerator level by rotating the
height adjusting screw. Carpet or floorcloth on
which a refrigerator is installed may be discolored
by heat from the bottom of the refrigerator. So,
it is necessary to place a thick pad below the refrigerator. |
|
 |
|
A proper distance
from adjacent items
Please keep the refrigerator at a proper distance
from other things. Too small a distance from adjacent
items may result in lowered freezing capability
and increased electricity charges consumption. |
|
 |
|
Where feed water
pipe can be easily connected in a dry place
Select a place where a feed water pipe can be easily
connected between the automatic ice maker and dispenser.
A wet or near-water place, refrigerator may be rusted
or electricity may be leaking. |
|
 |
|
Where is free from
heat or coal gas
Places where ambient temperature are high, freezing
capability is deteriorated and electric charge is
increased.
Coal gas and smoke may discolor the appearance of
refrigerator. |
|
|
|
NOTE
Install the refrigerator at a place where the ambient
temperature is 5¡ÆC~43¡ÆC.
Too high or low ambient temperature may cause functional
troubles. Also, the tube between the dispenser and automatic
ice maker may be frozen.
|
Door
Removal
If your access door is
too narrow for the refrigerator to pass the through,
remove the refrigerator door and pass the refrigerator
laterally.
 |
|
Remove lower
cover and then feed water pipe
Remove the lower cover by lifting upward,
and then pull up the feed water tube while
pressing area shown in the figure to the right.
NOTE
If a tube end is deformed or abraded, cut
the part away. |
|
 |
|
Remove the
freezer compartment door
1) Separate all connection wires except for
the earth line after removing the hinge cover
by loosening the screws.
2) Remove the keeper by rotating it to counted
clockwise (¨ç) and then lifting the upper hinge
up (¨è).
NOTE
In removing the upper hinge, be careful so
that the door does not to fall over frontward.
3) Remove the freezer compartment door by
lifting it upward. This time, the door should
be lifted enough for the feed water pipe tube
to be completely pulled out.
NOTE
Move the refrigerator compartment door passing
through the access door and laying it down
but be careful not to damage the feed water
pipe tube. |
|
 |
|
Remove the
refrigerator door
1) Loosen the hinge cover screws and remove
the cover. Remove all connection wires, if
any, except for the earth line.
2) Remove keeper by rotating it clockwise
(¨ç)
and then remove the upper hinge by lifting
it up (¨è).
3) Remove the refrigerator compartment door
by lifting it up. |
|
 |
|
Pass the refrigerator
Pass the refrigerator laterally through the
access door as shown in the right figure. |
|
|
|
 |
Mount
the freezer and refrigerator compartment doors
Mount them in the reverse sequence
of removal after they pass through the access door.
Feed
water pipe Installation
Before installation
· Automatic ice maker operation needs water pressure
of 147~834 kPa (1.5~8.5kgf/§²) (That is, an instant paper
cup (180 cc) will be fully filled within 3 sec.).
· If water pressure does not reach the rating 147
kPa (1.5 kgf/§²) or below, it is necessary to purchase
a separate pressure pump for normal automatic icing and
cool water feed.
· Keep the total length of the feed water pipe
tube within 12 m and be careful for the tube not be bent
straightly. If the tube is 12 m or longer it may cause
trouble in water feed owing to the drain water pressure.
· Install the feed water pipe tube at a place free
from heat.
Warning
· Connect to potable water supply only. |
|
|
